23 by 23 by 13-1/2 inches; 68-1/2 pounds; 1-year warranty Includes DEWALT synthetic compressor oil and pressure regulator Cylinder constructed of cast iron 4-1/2 cfm delivered at 100 psi; dual soft start valve for cold-weather starts; oil-lubricated pump 15 amp 2-3/4-horsepower 4-gallon oiled twin hot dog compressor with carrying handle
found in D55155's description: com Review
At just a foot high and less than two feet wide out of the carton, this compressor was quite a bit smaller than we expected, so to be fair, we quickly lowered our expectations. The joke was on us, though, because this little powerhouse just doesn’t quit, and we learned that you can’t judge a compressor by its size. Emglo’s half-century in the compressor business is evident in this model, and with a couple of small exceptions (we’ll get into that in a minute), we don’t think anyone could make a finer piece of air power. To let out any moisture that’s accumulated, it’s just an easy turn of the ball-valve tank drain, then just wrap the cord on its holder and you’re ready to go. Now, this may be a plus or a minus in your book, but we liked the fact that the compressor is factory set to power on at 100 psi an+d shut off at 120 psi, and the cycle time was under 15 seconds.) It has air aplenty for two nailers at once, and with that fast recovery, the job will get done in no time.
In balance, this is one of the best compressor’s we’ve seen for the size, power, ruggedness and incredible portability it offers. Here’s to a great pairing of two great toolmakers.--Kris Jensen-Van Heste
Product Description
DeWalt's 2-horsepower, 4-gallon compressor features an oil-lubricated design with a cast-iron cylinder to guarantee job site durability. The new roll-cage design and integrated control panel protects the compressor and the controls from accidental damage. Carrying the compressor is easy, too: the flat design lets the user tote the compressor comfortably like a suitcase. Other features include a ball-type tank drain and a wrap area to store the power cord. The 4-gallon tank is ASME approved and CSA certified. The package comes with the initial fill of DeWalt synthetic aircompressor oil.
From the Manufacturer
This 4-gallon hand-carry compressor was designed to meet the tough demands of the job site. The handle is situated to allow the user to carry the compressor with one hand in a natural walking position. The roll cage and integrated instrument panel protect the compressor and instruments from damage. Other features include a ball-type tank drain design and a wrap area for securing the power cord. The 4-gallon tank is ASME-approved and CSA-certified. Comes with the initial fill of DeWalt's synthetic aircompressor oil.5 cubic feet per minute delivered at 100 psi, recovers in less than 15 seconds
New ergonomic design for easy portability
Protected components for maximum durability
Oil-lubricated pump allows for increased life
ASME-coded, 4-gallon, OSHA-recognized tank
Dual soft-start valves assist in cold weather startup
Ball valve drain allows for quick and thorough tank draining
Cast-iron cylinder enhances pump life
CSA approved
Specifications
Drive: direct drive
Horsepower: 2-3/4 max hp
Tank size: 4 single ASME tank gallons
Power supply: 120-volt AC, 15 amps, 60 Hz, 2-pole induction motor
Cubic feet per minute at 100 psi: 4.
Includes
DeWalt synthetic compressor oil
2 universal quick couplers
Regulator
Warranty This DeWalt high-performance industrial tool comes with a warranty package that includes: 30-day, no-risk satisfaction guarantee One-year free service contract One-year warranty
Product Description
2 HP, 4 Gallon, Electric Single Tank Hand Carry Compressor, 4.5 CFM @ 100 PSI, Ball Tank Drain Valve Allows For Quick & Thorough Draining, Oil Lubricated Pump Allows For Increased Life, Cast Iron Cylinder Increases Life Of The Pump, Dual Soft Start Valves Assists In Cold Weather Start Up, Improved Ergonomics Assists In Carrying, Protected Components For Increased Durability, ASME Coded 4 Gallon Tank Is OSHA Recognized, CSA/NRTL Approved, Tool Length: 21.
found in D55155's reviews: dewalt has never let me down - most of my tools are dewalt including a assortment of nailers and this compressor.its great!!never short on air supply,even when framing.roll cage protection is much nicer then old twin tank setup.as for noise,aircompressors make noise but this unit is not bad,its a lot nicer on the ears then my 30 gallon unit. the only thing that would make this unit more attractive would be wheels and a self-storing handle like porter cable offers on its single tankcompressors,other then that i have no complants. Good machine, but some packaging and assembly issues - To my dissatisfaction, it arrived with a broken air filter and some loose items rolling around in the airtank. No, it wasn't the air filter parts, it was something metalic actually inside the closed tank! Amazon referred me to DeWalt who referred me to my local service center. DeWalt was nice enough to agree to send a replacement filter, but I returned the unit to Amazon because of the loose items in the tank.
Thanks to Amazon's incredibly fast and hassle-free process for returns, I had my replacement compressor less than a week later. Unfortunately, it too had a broken air filter. But since everything else was fine, I bought a filter locally (DeWalt's replacement has yet to arrive) for $10 and kept the compressor. This was not in the first shipment and is REQUIRED before starting the unit which is something that as a first-time compressor buyer, I would not have known to do. That kind of transition can lead to inconsistencies in fabrication and packaging like I have experienced, but I'm hopeful that the core design and construction of the pump and tank is solid and I like the way the machine works so I'm keeping it. A very good compressor - I replaced my hotdog style oil-less compressor when the connecting rod decided to break.
While at the local hardware store I saw the DeWalt D55155 compressor and thought, "geez, you could not miss that compressor!" The bright yellow paint made this compressor stand out and then that's when I saw the name Emglo. It has a 4 gallon tank, two connectors on the front, an easy to use regulator and gages that are protected by the heavy roll frame and face plate. This compressor also has a ball valve on the bottom of the tank for easy draining. This ball valave is also inside the frame as is every component of the compressor. It's mounted inside the roll cage near the copper line running from the compressor to the tank. It might be, but, I put the compressor away from where I'm working so this is not an issue.
As with any compressor you have to keep the extension cords short.
So, would I buy this compressor again if I had to? You bet!. Paradox - I just pulled the compressor out of the box and was mightly impressed. It filled the tank quickly and quietly. Other tools - However, I use it primarily with other air tools including an impact wrench. I was a little worried about the 4 gallon reserve tank handling my impact wrench air volume which is the most common tool I use for odd jobs. JUST WHAT I NEEDED - I AM A BUILDER BY TRADE AND I HAVE A 8HP GAS COMPRESSOR FOR MY LARGE JOBS. I HAVE HAD SEVERAL EMGLOW COMPRESSORS AND THIS HAS MET EVERY JOB I BOUGHT IT FOR. IF YOU NEED MORE AIR THEN I WOULD CONSIDER A 2 HP OR MORE SETUP. I LOVE THE HANDLE AND THE BALANCE OF IT TO CARRY AND LOAD IN THE TRUCK WITHOUT TIPPING OVER THE STACKED TANK MODELS WOULD FALL OVER OR ROLL AROUND THE TRUCK. THAT MAKES THE CONTROLS FAIRLY WELL PROTECTED. Best investment yet - I just use short blasts of air and let the unit catch back up if I want to dust something off. Little heavy, but for long distances I have learned to grab the tank like a heavy piece of fire wood with the unit up to your chest and it is not bad.(longer air hose is better) . Best light duty unit for the money - But, as some of the other reviews have stated, this unit is not for heavy duty operation that would entail the use of spray guns, air sanders or all day feeding of multiple framing nailers. I have since replaced this unit with a simular $210 Hitachi twin tank unit (3 stars) that has worked fine for over a year after this one disappeared off a job site. Solid Performer. - I am a general contractor who needed a better compressor to do small framing jobs and finish jobs on site. Mine was a reconditioned unit and I have never experienced any problems and I use it, the larger tank does need to be drained regularly though, overall good compressor. DeWalt takes a classic to a new level - Last yearI spent many months researching a replacement for my ailing Campbell-Hausfeld oilless compressor. Originally I figured the CH had a higher air output, needed no oil changes,would work on slopes and start in cold weather.After forking over the big bucks and putting it to work for DeWalt's 30 Day trial period I couldn't believe I'd gone so long without this compressor. 1) First of all the Emglo name on the unit reassured me that I was getting a tool built by the industry leader with a great reputation for tough, dependable compressors. The first day on the job proved it with quick cycling times and ample air at all times. I do a lot of work in luxury high rises and I've often left the compressor at home rather than drag it down endless corridors. I've paid for the compressor already in labor savings by bringing it to every trim job. I've had othe craftsmen come over and ogle the compressor and ask questions about it, but mostly admiring it.
In short, this is a serious tool for the professional contractor with loads of power(delivered air), durability, great design and looks. My only complaint is the air release lever, an otherwise solid unit mounted on the underside of the tank. The opening is too narrow for your hand and the sharp stream of air can actually cut your skin. In addition the compressor shoots out small chunks of ICE from the tank creating dangerous projectiles that will cut your hand or riccochet into your eye. Finally, I have a compressor that won't roll around in the back of the truck knocking off gauges and connections as I drive through the city. Dewalt and Emglo make a complete package, great compressor! - Someone decided they needed my trim compressor more then I did so I had to purchase another one. I must admit I was not to broken harted about it though because I have had my eye on Dewalt's new compressor now for some time. The sleek design, the way it protects its gauges, and its 2 quick conect air ports kept calling me every time I saw this compressor. I was not disapointed!! The unit is a little heavy for a portable compressor at over 60 lbs. Inside a house a compressor's noise can seem to be greatly magnified but this unit seems almost quiet, it runs so smooth. I had a larger compressor for framing but this Dewalt compressor has done so well that I have sold my larger one and rely on just this one. The unit really has no real flaws at all the air drain has a great little lever to drain the tank with, but it does blow out hard if you open it to quick and I am not convinced it drains all the condesation real well. There is a little black breaker on the compressor unit which can be a little dificult to locate and reset, it would be nice if on a newer version Dewalt would move it to the front with the gauges and quick connects. It has triped several time on us if we try and run too many things at a time such as a miter saw, table saw, and the compressor, but for normal use the draw of this compressor seems fine even on a 15amp breaker. To sum it all up this is one really nice complete package compressor!! It is small enough for the little jobs yet tough enough for the more demanding jobs, within reason, remember it is only a 4 gallon, running at less the 15amp, compressor. With Dewalt and Emglo combine you will not go wrong buying this compressor, and unless you get a defective unit which happens with all products from time to time, you will have a compressor that should last a long time.
Baja style metal gauge guards protect gauges from job site damage Innovative integrated control panel with dual air outlets for the ultimate in user convenience Full-roll cage and patented skid plate protection for extreme job site durability Oil lubricated pump with cast iron lined cylinder for long life Powerful high performance 2.0 HP induction motor for fast pump up and recovery times
found in CAP2045ST-OL's reviews: Oil ? - I have had this compressor for a couple of years now, never had a problem with it so far. I would say it's not exactly the lightest portable compressor out there, and most of the time I wish it had wheels. I have another larger more stationary compressor that is a different brand that gets used more out in the main shop. There are a few minor flaws that could be fixed relatively easily with this compressor. The air filter sticks out of the cage a little too far, looks like it's prone to bumps. And last but not least, the control panel, nice easy access and readability, and I like the dual air outlets, but they stick out of the roll cage after you install a pair of female couplers. Otherwise it seems like a good unit, it doesn't take long to cycle on an empty tank.
32 pounds; 1-year warranty Includes compressor, ASME safety valve, regulator, gauges, 1/4-inch quick coupler, manual Cast-iron construction Provides 3.7 cfm at 40 psi and 2.6 cfm at 90 psi; air-regulator and quick-connect coupler 15 amp, 2-horsepower, 6-gallon oil-free pancake compressor; handle; built-in thermal overload protector
found in CPFAC2600P's description: com Review
This Porter-Cable 2-horsepower, 6-gallon pancake compressor transports easily but has plenty of capacity and power--enough to support heavy use of brad and finish nailers and moderate use of framing nailers. Features include a high-flow regulator, an easy-to-read air pressure gauge, automatic thermal overload protection, an industrial-style quick-connect body in the air outlet, and a long-life motor with replaceable brushes. The compressor weighs 32 pounds and has a handle built into the motor housing, so it's relatively portable. This Porter-Cable is as convenient and easy to use as any compressor out there, and it's just about ideal for brad and finish nailers that are being used inside people's homes on a regular basis. --Jonathon Tudor
From the Manufacturer
This oil-free 2-hp pancake-style aircompressor has a new high pressure design that provides 28-percent more usable air! This allows more run time and less down time. The high-flow regulator keeps the tank pressure between 120 PSI and 150 PSI, allowing a greater reserve air capacity. Lightweight for portability, this compressor has plenty of power to fire all brad and finishing nailers as well as moderate usage of roofing and framing nailers. Includes compressor, high flow air regulator and gauges, quick coupler, and instruction manual.8 HP Running
Built-in automatic thermal overload protection
Larger Easy to read regulated air pressure gauge
Universal, High-FloSM, push-to-connect coupler in air outlet
One year warranty
150 PSI - 10 gallon equivalent tank size as compared to conventional 125 PSI model
87 Dba
Oil-free pump design for durability and no maintenance
Long-life motor with replaceable brushes
High-FloSM air regulator for more work at higher pressure (125 PSI start and 150 PSI stop pressure switch)
6 gallon tank supports heavy usage of stapler, brad and finish nailer, standard-to-heavy roofing and standard framing nailer
120 Volt, universal motor starts easily under low voltage conditions
Extension cord use without tripping circuit breakers
Standard Equipment: Compressor, ASME safety valve, air regulator and gauges, 1/4" quick coupler, and operating manual
SPECIFICATIONS
Lubrication: Oil Free
Gauges: 2
Quick Couple: 1/4" NPT
Weight (Lbs.): 39
Tank Size Gal. PSI: 150
SCFM Air Delivery @40 PSI: 3.7
SCFM Air Delivery @90 PSI: 2.
Product Description
2 HP, 6 Gallon, Oil-Free Pancake AirCompressor, 150 PSI Maximum Tank Pressure, 3.6 SCFM @ 90 PSI 87 DBA, 15 AMPS, Built-In Thermal Over Load Protection, Hi-Flo Air Regulator With Quick-Connect Coupler, Regulated Pressure Gauges, Includes ASME Safety Valve, 1 Year Warranty.
found in CPFAC2600P's reviews: Plenty of Gas - It's a little loud while filling it's tank but I can live with that based on it's performance. A good Specialized Compressor - This compressor is great for what it was designed for. And, that was an intermittant duty compressor for single nail gun operation. Now this kind of motor is very powerful for its size and weight, but it cannot match the heavier and larger brush free induction motors of larger compressors. I use this compressor with great satisfaction running some trim and 15 gauge nailers. If rewiring your wifes toaster brings on a cold sweat, you will need to bring this compressor to an authorized service center as well as your bank card. The compressor is oil less, so along with less maintanance, less mess on wood work and so on will be realized. I really like the rubber hose connecting the compressor section from the tank. The hose should last the life of the compressor which will be quite a long time if you use the unit within its stated design parameters. Once pneumatic, you never go back - The Porter-Cable 2HP 6-gallon pancake compressor is a reasonably powerful and reasonably portable aircompressor. I only recently purchased one but I am already sold on pneumatic tools, which the PC 6-gallon compressor operates surprisingly well. Although many pneumatic tools, such as air hammers, drills, and sanders, consume quite a bit of air (generally in the neighborhood of 5 CFM at 90 PSI), I have found that my PC compressor does just fine with its modest 2. Unless you need to operate the tools continuously for long periods, the 6-gallon tank provides sufficient ballast to keep them happily buzzing and spinning at full power. My one complaint is that the motor and compressor are a bit louder than I expected. Then again, the noise of the compressor is hardly noticeable above the din of an air hammer, so I'm not sure it really matters.
If you enjoy using power tools and you have not yet experienced the pleasures of pneumatic gizmos, you should consider purchasing a small but serious compressor like the PC 2HP 6-gallon pancake. It's truly amazing how versatile compressed air is; basically any tool that runs on electricity also comes in a pneumatic version (well, except for arc welders).
But be warned! If you take the plunge into pneumatic tools, there is an endless stream of items you will find yourself purchasing: air tool lubricants and cleaning kits, in-line oilers, air hoses and gauges, quick connectors, air filters, oil-water separators, Teflon tape, universal air hose joints, air manifolds, blowguns with assorted nozzles, etc.)
One odd thing I've noticed is that the PC 6-gallon compressor is virtually identical to the Craftsman 6-gallon compressor, right down to the paint job.
12-Month limited warranty Electric direct drive and oil splash lubricated for longer life Superior Quality Speroni?® pump Life expectancy of up to 8,000 hours Contractor grade, 3 HP (peak), 4.2 gallon capacity
found in GR2500's description: These same principles are now reflected in Grip-Rite's line of professional quality tools and compressors. This is currently Grip-Rite's flagship compressor for good reason. The pontoon-style tank design of this unit was intended to minimize tip over while still offering enough air to handle nearly any job.2 gallon tank, 64 lbs total weight, 55 second pump up, 14 second recovery, and 135 max psi, 14. Compare to: Hitachi EC119, Porter Cable Job-boss Model #C3551, Porter-Cable CPLDC2541S, Porter-Cable CPLDC2540S, Rol-Air The Bull.
85 pounds; 1-year warranty Includes compressor, mobility kit, and manual Cast-iron construction 2-port removable console for remote air regulation; full roll cage to protect kit; 150 max psi 15 amp, 3-1/2-horsepower, 4-1/2-gallon oil-free wheeled single hot dog compressor with handle
found in C3151's description: com
Porter-Cable’s solved the compressor mobility problem on two levels with this tool. First, and most impressively, it’s got a two-port removable console for remote air regulation and higher air pressure right where you’re working. And the compressor itself has wheels and an extension handle, making life easier on you.
Let’s face it: This compressor’s big, heavy and loud, with a max psi of 150. You can run three or four guns at once off it with a splitter and have no air supply problems whatsoever.5 gallon, oil-free contractor style compressor is packed with features. It also packs 150 PSI in the tank for longer tool run time. The high-flow air regulator and two-port removable console are winning combinations for contractors. Having the ability to remove the console gives the user the opportunity to remote air regulation and gain higher air pressure closer to the job site.
Technical Details Tank capacity: 4. Air delivery at 40 PSI: 7.
What's in the Box C3151 Job Boss Compressor, mobility kit, manual.5 gallon, oil-free contractor style compressor is packed with features. It also packs 150 PSI in the tank for longer tool run time. The High-flo air regulator and 2-port removable console are winning combinations for contractors. Having the ability to remove the console gives the user the opportunity to remote air regulation and gain higher air pressure closer to the job site.
Product Description
Includes Compressor, Mobility kit, ASME safety valve, Operating manual, Limited one-year warranty.
found in C3151's reviews: way to go portercable - This the best compressor on the market it keeps up with 2 framing nailers with no problem all day this machine is for constuction not for paint gun with high volume you need a bigger tank 10 gallion or bigger. Used it today for the first time - I use an air hammer to break out the old windows and they require a lot of air. This compressor worked well with some catch up time but hey, it's only a 4 1/2 gallon tank. Cord wrap is fairly useless, handle makes it portable, regulator worked, switch and air release are protected. Dependable and... dependable - I've been using this compressor for about 3 months now. Nailing, stapling, and air cleaning. What I don't particularly care for about the unit is the airflow adjustment valve. and I don't trust it for the compressor's duraction.
05 update: I noticed one reviewer griped about this tank's compressor turning on frequently while using an air wratchet or something. that's an unfair assessment. Using such tools would cause the same reaction on any tank with the same air gallon capacity.
Three year limited warranty Full roll cage with high flow regulator and dual quick-connects Patent pending oil-lube system with ball bearing design Direct drive, no belts or adjustments are necessary 2.5 HP, 4.3-gallon oil-lube compressor
found in CPLDC2540S's description:From the Manufacturer
Porter-Cable is proud to introduce our first oil-lube compressor. When we first put our engineers on the task of designing an oil-lube compressor we gave them one priority; it could not have the same imported pump as all the other major brands have. Just as in a car, the lubrication system in the pump is the most vital part in a compressor. Now, take this revolutionary pump engineered for maximum durability and life, and add in the "High Pressure Technology" and you have compressor that will run at 150 pounds per square inch (PSI).5 horsepower induction motor is safely shrouded and acts as a wind tunnel providing more than enough air to cool the unit down even under the most strenuous conditions. oil capacity to assure long life
Patented oil lubrication system allows pump to be operated on an uneven surface
Protected panel includes two universal High-FloSM push-to-connect couplers and larger, easy to read regulated air pressure gauge
150 PSI tank pressure, equivalent to a 7.3 gallon tank at 125 PSI, for 71% more stored work capacity
83 Dba
Higher 120 PSI cut-in pressure assures nails will be completely driven in before pump cycles on
Two pole, 3,450 RPM capacitor start induction motor for maximum air delivery
High-FloSM air regulator for more work at higher pressure (125 PSI start and 150 PSI stop pressure switch)
Specially designed protective transport handles
Low 12 Amp motor draw prevents accidental tripping of circuit breakers
4 gallon storage capacity airtank supports heavy usage of stapler, brad, finish, roofing and framing nailer
Standard Equipment: Compressor, ASME safety valve, air regulator and gauge, 1/4" quick coupler, oil, and operating manual
Provides storage for air hose Includes dual quick connects for two separate air lines Provides up to 5000 hours of pump life
found in EX8200's description: It also offers a convenient control panel, hose rack, 26-gallon ASME tank code and compressor oil. This compressor is ideal for automotive and job site tasks.
Product Description
mfr: Campbell Hausfeld Air Products Campbell Hausfeld takes performance to the max by launching Maxus, a new brand of heavy-duty powered equipment for contractors and serious do-it-yourselfers.
Premium Cast Iron Single Stage Oil Lubricated Compressor - Commercial Model - 2 HP Running, Oil Lubricated, 26 Gallon Tank (Five Year Limited Warranty).
Delivers 4 avg scfm @ 90 psi Delivers 4 avg scfm @ 90 psi for medium duty pneumatic tools Crankcase design is up to 25 percent larger than competitive models for improved performance and less oil carryover Cast iron oil-lubricated pump for long lasting, reliable performance 4-gallon twin stack tank design for portability
found in HL5502's description:From the Manufacturer
Even for occasional home maintenance, air tools are more practical and less costly than expensive electric power tools with umpteen mechanical parts and exorbitantly priced batteries of all shapes and sizes. But before investing in smart air tools, you need a quality compressor. This popular 4-gallon twin stack aircompressor from Campbell Hausfeld is oil lubricated and built to last. Ideal for inflation, nailing, stapling and spraying jobs, this compressor also powers everything from sandblasters and spray guns to drills and die grinders in a matter of seconds. So, rather than investing in an expensive new electric tool set; save time and money with this 4-gallon compressor and Campbell Hausfeld's line of 70 high quality air tools. The initial cost of an air tool is significantly lower than its electrically powered counterpart, and the average tool life expectancy is longer, too. Plus, when powered by this 4-gallon compressor, air tools deliver more torque and higher revolutions-per-minute than electric tools for less downtime and greater productivity.
FEATURES
4-gallon twin stack tank design for portability
Cast iron oil-lubricated pump for long lasting, reliable performance
Crankcase design is up to 25 percent larger than competitive models for improved performance and less oil carryover
Delivers 4 avg scfm @ 90 psi for medium duty pneumatic tools
SPECIFICATIONS
Output: 4 avg scfm @ 90 psi
Type: oil-lubricated
Capacity: 4-gallon
.
found in HL5502's reviews: The facts about this aircompressor - Don't believe everything that the editors at Amazon wrote about this compressor. With those jobs you need a large tank capacity like over 20 gallons at least, this compressor only has 4 gallons. Yes it is true what the other reviewer said, this compressor is loud, but what do you expect all aircompressors are relatively loud. And yes this compressor is heavy I think it's about 70 lbs. Hitatchi's twinstack oil-lube version is about the same as this compressor but goes for twice the price. Other than that I think that this compressor is a buy because it's oil-lubed (more reliable than oil less), affordable, and made by a company that is known for it's aircompressors.
Run multiple tools from dual universal quick couplers Top load panel with positioning holes allows unit to transport loads up to 100 lbs 10" pneumatic wheel and handle kit for ease of mobility Oil lubricated pump with cast iron cyliner enhances pump life 4.0 CFM delivered at 90 PSI pump provides rapid recovery
found in D55154's description:From the Manufacturer
DEWALT designed its first oil-lubricated, wheeled compressor to provide end users with increased durability, ease-of-use, and performance. Durability-The heavy-duty reinforced frame allows the compressor to withstand the harshest jobsite conditions. The couplers and gauges are well guarded by the tank assembly, protecting these important components from routine wear and tear. In addition, the D55154 was built with a rugged 3/4 foot, which is less susceptible to being broken and knocked off the unit, compared to other compressors on the market.5 frame clearance and 10 solid-axle, fully pneumatic tires, the compressor can be easily transported on jobsite terrain. The D55154 features an ergonomic telescoping handle and also includes a transport platform, or dolly, on top of the deck, allowing users to tie down additional equipment to the top of the compressor and easily move it to various locations. For increased efficiency, the oil pump has been rotated 90 degrees, providing easy access to check and change the oil, as well as a ball drain valve for quick and thorough tank draining.
Slow turning 1700 rpm motor draws 13 amps
