Air compressor pump part - Porter-Cable CPLDC2541S, Porter-Cable CPLDC2540S, Palmgren 92111, Bostitch CAP2560OL, Hitachi EC25E, DeWalt D55155R, Bostitch CAP1580WB, Campbell Hausfeld EX8401, Bostitch CAP2045ST-OL, Campbell Hausfeld EX8000

Air Compressor Pump Part - 1 2 3 4 5 6 7 8

*2.5 HP 4 Gallon Oil-Lube Air* Compressor \| Porter-Cable CPLDC2541S**
	$369.99 >> $358.51 by Porter-Cable Three year limited warranty Complete with high-flow regulator and quick-connect, pressure gauge and tank gauge Patent pending oil-lube system with ball bearing design Direct drive, no belts or adjustments are necessary 2.5 HP, 4.3-gallon oil-lube compressor found in CPLDC2541S's description: From the Manufacturer Porter-Cable is proud to introduce our first oil-lube compressor. When we first put our engineers on the task of designing an oil-lube compressor we gave them one priority; it could not have the same imported pump as all the other major brands have. So, in true Porter-Cable fashion the engineers came up with a completely different pump. Just as in a car, the lubrication system in the pump is the most vital part in a compressor. That is why this unit was designed with a patent pending oil slinger design as an integral part of the crankshaft that continues to lubricate the piston in any angle. The design features don't stop there; it boasts a cast-iron cylinder, stainless steel Swedish valves, and an automotive type paper filter to trap unwanted particles before they enter the system. Now, take this revolutionary pump engineered to last over 3,000 hours of use and add in the "High Pressure Technology" and you have compressor that will run at 150 pounds per square inch (PSI). The large bore and short stroke were design to pump out 5.5 horsepower induction motor is safely shrouded and acts as a wind tunnel providing more than enough air to cool the unit down even under the most strenuous conditions.3 HP Running Patented oil lubrication system allows pump to be operated on an uneven surface Universal, High-FloSM, push-to-connect coupler in air outlet 150 PSI tank pressure, equivalent to a 7.3 gallon tank at 125 PSI, for 71% more stored work capacity 83 Dba Higher 120 PSI cut-in pressure assures nails will be completely driven in before pump cycles on Two pole, 3,450 RPM capacitor start induction motor for maximum air delivery High-FloSM air regulator for more work at higher pressure (125 PSI start and 150 PSI stop pressure switch) Low 12 Amp motor draw prevents accidental tripping of circuit breakers 4 gallon storage capacity air tank supports heavy usage of stapler, brad, finish, roofing and framing nailer Heavy duty cast iron cylinder construction and large 8 oz. oil capacity to assure long life Standard Equipment: Compressor, ASME safety valve, air regulator and gauges, 1/4" quick coupler, oil, and operating manual SPECIFICATIONS Lubrication: Oil Lube Gauges: 2 Quick Couple: 1/4" NPT Weight (Lbs. PSI: 150 SCFM Air Delivery @40 PSI: 5.4 SCFM Air Delivery @90 PSI: 4. found in CPLDC2541S's reviews: Does it job w/ no problems - Unless I just happened to get a good one; I have had no problems w/ this compressor. It is the garage compressor and is exposed to humidity of 70% or more and temps from 33-90's. Pump shuts off at in around 150psi. I have use it to pump car tires, run air nailers,a small porter cable detail spray gun and even a ingersol rand 1/4" air rachtet. I have changed oil once and air filter once. Takes to much power and is too loud (also flimsy switch) - This compressor absolutely will NOT run on 15 amps. This makes this compressor almost usless for me because I can never find anywhere to plug it in. I was just working in a basement at the same time as a guy that had a Hitachi compressor and his was less than HALF as loud. The guy helping me tripped over the air hose and it caught on the little shutoff lever. Now my compressor won't even shut off. If you leave it run it will pump up to 175 psi and then blow the relief valve. I'm seriously thinking about just leaving this for the garbage man and buying the DeWalt Emglo compressor. I ended up buying a CastAir air compressor. CastAir is not a commercial brand, but the factory where they are made is about 2 miles from my house in Chaska, MN. These compressors were only recently made available to non-commercial applications (previously they specialized in huge compressors used in body shops, etc. It's quiet, powerful, and SOLID as a ROCK!!! A REAL contractor grade compressor for the same amount as I paid for this PC. I have NO relationship or incentive to recommend CastAir other than I'm a very satisfied customer. Check them out if you want a REALLY great compressor.
*2.5 HP 4 Gallon Oil-Lube Air* Compressor \| Porter-Cable CPLDC2540S**
	$580.00 by Porter-Cable Three year limited warranty Full roll cage with high flow regulator and dual quick-connects Patent pending oil-lube system with ball bearing design Direct drive, no belts or adjustments are necessary 2.5 HP, 4.3-gallon oil-lube compressor found in CPLDC2540S's description: From the Manufacturer Porter-Cable is proud to introduce our first oil-lube compressor. When we first put our engineers on the task of designing an oil-lube compressor we gave them one priority; it could not have the same imported pump as all the other major brands have. So, in true Porter-Cable fashion the engineers came up with a completely different pump. Just as in a car, the lubrication system in the pump is the most vital part in a compressor. That is why this unit was designed with a patent pending oil slinger design as an integral part of the crankshaft that continues to lubricate the piston in any angle. The design features don't stop there; it boasts a cast-iron cylinder, stainless steel Swedish valves, and an automotive type paper filter to trap unwanted particles before they enter the system. Now, take this revolutionary pump engineered for maximum durability and life, and add in the "High Pressure Technology" and you have compressor that will run at 150 pounds per square inch (PSI). The large bore and short stroke were design to pump out 5.5 horsepower induction motor is safely shrouded and acts as a wind tunnel providing more than enough air to cool the unit down even under the most strenuous conditions.3-gallon side stack design incorporates a complete roll cage that protects the dual high-flow quick-connects, the high-flow regulator and pressure gauge as well as the motor and pump. oil capacity to assure long life Patented oil lubrication system allows pump to be operated on an uneven surface Protected panel includes two universal High-FloSM push-to-connect couplers and larger, easy to read regulated air pressure gauge 150 PSI tank pressure, equivalent to a 7.3 gallon tank at 125 PSI, for 71% more stored work capacity 83 Dba Higher 120 PSI cut-in pressure assures nails will be completely driven in before pump cycles on Two pole, 3,450 RPM capacitor start induction motor for maximum air delivery High-FloSM air regulator for more work at higher pressure (125 PSI start and 150 PSI stop pressure switch) Specially designed protective transport handles Low 12 Amp motor draw prevents accidental tripping of circuit breakers 4 gallon storage capacity air tank supports heavy usage of stapler, brad, finish, roofing and framing nailer Standard Equipment: Compressor, ASME safety valve, air regulator and gauge, 1/4" quick coupler, oil, and operating manual SPECIFICATIONS Lubrication: Oil Lube Gauges: 2 Quick Couple: 1/4" NPT Weight (Lbs. PSI: 150 SCFM Air Delivery @40 PSI: 5.4 SCFM Air Delivery @90 PSI: 4. found in CPLDC2540S's reviews: *A- compressor* except for the regulator - I've been searching for a portable compressor for a couple of months now and near the end came up with three to chose from: the Emglo 55155, a Hitachi dual stack and this PC. Other compressors did meet these, but what draw me was the oil lube system that permits you to use it on uneven surfaces.5max) to not trip the circuit breakers, filtered intake (not output though) for longer motor life, shrouded motor for airflow from fan and good manual. The small metal cup also bit part of the plastic grommet retainer. The only thing I added at the universal coupler end is a water/air** filter.

*4.2 Amp 1 Horsepower 1 Gallon Oil-Free Single Hot Dog Compressor* \| Palmgren 92111**
	$129.99 >> $131.72 by Palmgren Die cast aluminum pump with cast iron sleeve (oilless) Compact design very lightweight Direct drive Oilless pump has sealed bearings on all reciprocating parts and Teflon-impregnated piston rings to reduce friction Manual reset overload protection found in 92111's description: From the Manufacturer This Palmgren DIY Series Air Compressor is perfect for the at-home hobbyist or for contractors who need a portable pneumatic power source, and it is oilless for maintenance-free operation. Compressor consists of a 1HP motor, single cylinder, single stage aluminum air compressor pump and a 1 gallon air tank. The pump runs very quietly, so that the compressor can be used in the same area that the work is taking place. Compressor is light weight and portable.
*15 Amp 2-1/2 Horsepower 6 Gallon Oiled Pancake Compressor* \| Bostitch CAP2560OL**
	$299.99 >> $299.99 by Bostitch 4.9CFM @40 and 3.6 CFM @90 Synthetic pump oil for low temp operation Dual air outlets Cast iron pump cylinder for extreme durability 2.5 peak HP 15 amp induction motor found in CAP2560OL's description: 5 HP oil lube pancake compressor Product Description mfr: STANLEY BOSTITCH 2. OIL LUBE PANCAKE COMPRESSOR Features: Heavy duty induction motor, oil lubricated pump, with synthetic oil included, two outlets included. Aluminum pump housing with cast iron sleeve. Air delivery 4.
*5.5-Horsepower Air* Compressor \| Hitachi EC25E**
	$1,612.12 >> $1,018.95 by Hitachi 30 day satisfaction guarantee and one year warranty on parts and labor Twin drain locks Cast iron pump Twin 4 gallon tanks 5.5 hp Honda engine found in EC25E's description: From the Manufacturer The EC25E is a commercial grade gas drive compressor from Hitachi.5hp Honda engine coupled with a unique cast iron pump. The 10-inch fly wheel includes a baffle to direct cool air towards the pump. Product Description Hitachi EC25E is a commercial-grade gas-driven compressor from Hitachi.5-horsepower Honda engine coupled with a unique cast-iron pump. The pump and crankcase feature oil-splash lubrication and a ball-bearing-mounted crankshaft, ensuring the compressor will be running for years to come. The unit's twin draincocks, one of each of the 4-gallon air tanks, makes it easy to purge the tanks of compressed air and condensation, helping prevent internal corrosion. In addition, the EC25E's large canister intake filter keeps the air running through the compressor and your nailer clean. The 10-inch flywheel includes a baffle to direct cool air towards the pump.
15 Amp 2-3/4 Horsepower 4-Gallon Oiled Single Hot Dog Compresso \| Factory-Reconditioned DeWalt D55155R
	$419.99 by DeWalt One-year warranty through the Dewalt factory or an authorized service center Oil lubricated pump allows for long life Cast iron cylinder enhances pump life Dual soft start valves assist in cold weather start up 4.5 cfm
*1.5 HP Electric Wheelbarrow Air* Compressor \| Bostitch CAP1580WB**
	$1,000.00 by Bostitch Large gauges provide a clear view of both tank and regulated air pressure Innovative, integrated control panel for the ultimate in user convenience Full roll cage protection for extreme job site durability Oil lubricated pump with cast iron cylinder for extreme durability 1.5 HP motor for fast pump up and recovery times

Maxus EX8041 15 Amp 3 Horsepower 60 Gallon Oiled Vertical Compressor
	$499.99 >> $499.98 by Campbell Hausfeld 3-horsepower motor for heavy duty air tool applications Up to 5,000 hours pump life for unsurpassed reliability Cast iron pump for optimal durability 60 degrees cooler than aluminum pumps with cast iron sleeves Over 35 percent quieter and than aluminum pumps with cast iron sleeves found in EX8401's description: From the Manufacturer Equipped with a 100 percent cast iron pump, the Maxus 60-Gallon Air Compressor outlasts and outperforms aluminum pumps for cleaner painting applications and more reliable air tool operation. This rugged, two-cylinder, oil-lubricated pump offers up to 5,000 hours of pump life. It’s over 35 percent quieter than aluminum pumps with cast iron sleeves and operates 60 degrees cooler. A beefy, 3-horsepower motor cranks out 135 PSI for operating most air tools. A heavy duty air filtration system means clean painting applications and longer tool life. FEATURES Cast iron pump for optimal durability Up to 5,000 hours pump life for unsurpassed reliability 3-horsepower motor for heavy duty air tool applications Plenty of power for operating most continuous flow air tools Metal Solber air filter for clean painting applications SPECIFICATIONS MODEL NUMBER EX8401 RUNNING HP 3. LIMITED WARRANTY 3-5 Years CERTIFICATION ASME Product Description 3 RHP, 60 Gallon, Vertical Air Compressor, Solid, Cast Iron, Twin Cylinder, Oil Lubricated Pump, High Performance Motor, Metal Solberg Air Filter, Delivers 11.
*2 HP Oil-Lubricated Stack Tank Air* Compressor \| Bostitch CAP2045ST-OL**
	$529.99 by Bostitch Baja style metal gauge guards protect gauges from job site damage Innovative integrated control panel with dual air outlets for the ultimate in user convenience Full-roll cage and patented skid plate protection for extreme job site durability Oil lubricated pump with cast iron lined cylinder for long life Powerful high performance 2.0 HP induction motor for fast pump up and recovery times
*14 Amp 3-1/4 Horsepower 4 Gallon Oil-Free Twin Hot Dog Compressor* \| Maxus EX8000**
	$340.00 >> $341.99 by Campbell Hausfeld 4-gallon twinstack tank Dual quick connects on control panel Easy to use control panel Oil-free pump for low maintenance and easy operation High out-put motor for high performance found in EX8000's description: From the Manufacturer This compressor is ideal for job site work. It produces air flow needed to operate multiple nailers. The pump is virtually maintenance fee and starts easily in cold weather!.