Ball valve drain allows for quick and thorough tank draining Dual voltage feature allows easy switching from 120 to 240 volts Dual control feature allows start/stop or constant run option Twin cylinder, cast iron, oil lubricated pump 8.4 cfm delivered at 100 psi with 17-gallon tank
found in D55585's description:From the Manufacturer
You will never run short of air again with this 2-horsepower electric wheeled compressor supported by an ASME-coded 17-gallon OSHA-recognized tank. The user can quickly and completely drain the compressor by the ball valve drain, which won't clog like other models that use needle valves. The D55585 includes DeWalt's synthetic compressor oil and a 3/8-inch NPT pressureregulator.
Includes
DeWalt synthetic compressor oil
3/8-inch NPT pressureregulator
Warranty This DeWalt high-performance industrial tool comes with a warranty package that includes: 30-day, no-risk satisfaction guarantee One-year free service contract One-year warranty.
30-day satisfaction guarantee and one-year warranty on parts and labor 9 amp motor runs at 1,700 rpm, providing 4.1 cubic feet per minute of free air Line regulator with gauge Direct-drive electric motor 2.3 cubic feet per minute at 90 psi
One-year warranty Features 1/4 NPT soft seat drain valve Rugged cast-iron cylinder provides maximum durability Integrated high-profile panel houses regulator gauges and universal quick couplers Powerful 2-horsepower electric motor delivers 3.8 cfm at 125 psi
found in M800-HC4V's reviews: Handy little machine! -
My only problem with it when it arrived was a leak in the plastic line that equalizes the pressure between the tanks. Because the fittings use airpressure to seal themselves, you can pull the line right out of the fitting when there is no pressure in the tanks.
Three-year warranty 60-gallon tank supports heavy-duty, intermittent to continuous use of multiple tools Oil-lubricated pump with aluminum body and cast-iron cylinders for heat dissipation and durability 7 hp induction motor for efficient operation High-pressure technology provides more usable air for longer run time
found in CPLC7060V's description:From the Manufacturer
New from Porter-Cable! This heavy-duty stationary aircompressor has a high-pressure design that allows it to store as much air as a 77-gallon tank. This provides more usable air and longer run times between refills-it's like being able to fit 20 gallons of gas in a 15-gallon tank-you'll get more done! A 7 hp, 240-volt induction motor powers this unit for maximum efficiency. A higher operating pressure of 110 psi start and 135 psi stop, provides more operating power. Includes compressor, tank gauge, and operator's manual.0 HP Running
135 PSI - 77 gallon equivalent tank size as compared to conventional 125 PSI models
84 Dba
Single stage, oil lubricated pump designed with aluminum body and head for best cooling and cast iron cylinder sleeves for best wear
Pump contains automotive style pistons, rings, and connecting rod
240 Volt capacitor start induction motor with manual thermal overload protection
Large tank pressure gauge for easy visibility and better accuracy
60 gallon air tank supports heavy duty, intermittent/continuous multi-tool usage
Full-size belt guard
Patented automatic belt tensioning system
Standard Equipment: Compressor, ASME safety valve, tank gauge, oil, and operating manual
SPECIFICATIONS
Lubrication: Oil Lube
Tank Size Gal. PSI: 135
SCFM Air Delivery @40 PSI: 14.2
SCFM Air Delivery @90 PSI: 9.7
Pressure Release: YES
Regulator: NO
Gauges: 1
Weight (lbs.
found in CPLC7060V's reviews: So far so good - I've had this compressor for about a year and like it. I bought it when I switched to air tool sanding and it easily keeps up with that job. The manual advises you to releive the airpressure though the quick relief valve, automatically down to about 10PSI, then opening the water drain and closing the valve before restarting.
ASME coded 17-gallon OSHA recognized tank Automatic idle control for reduced fuel consumption Ball drain valve allows for quick and thorough tank draining Four cylinder, cast iron, oil lubricated pump for durability and reliability 9 HP Honda GX gas engine provides proven reliability and durability
found in D55275's description: It's powered by an 8-horsepower Honda engine with automatic throttle control to conserve fuel when air is not being used. Compressor includes a 3/8-inch regulator and the initial fill of DeWalt synthetic aircompressor oil.
Includes
DeWalt synthetic compressor oil
3/8-inch NPT pressureregulator
Warranty This DeWalt high-performance industrial tool comes with a warranty package that includes: 30-day, no-risk satisfaction guarantee One-year free service contract One-year warranty.
86 pounds; 2-year limited warranty Includes compressor, mobility kit, ASME safety valve, manual Cast-iron construction 12 amps; 150 psi, enough to operate 2 nailers at once; roll bar to protect motor and pump 2-1/2-horsepower 4-1/2-gallon oiled wheeled single hot dog compressor
found in C3551's description: If you're a contractor looking for the right compressor, you've found it.--Kris Jensen-Van Heste
From the Manufacturer
Why lift when you can roll? The Job Boss Compressor comes equipped with a mobility kit for job site portability.5 gallon, Oil-Lube contractor style compressor is packed with features you’ll like. The High-flo airregulator and 2-port removable console are winning combinations for contractors looking for performance and versatility. This compressor is designed with a removable console for maximum mobility and airpressure.5 HP single tank aircompressor
Oil-lube aircompressor for maximum durability
150-PSI tank pressure for longer tool run time,
Quieter motor is easy on eardrums
120 V/ 60 hertz/1 phase motor
Two pole, 3450-RPM capacitor start induction motor for maximum air delivery
Includes 1-year limited warranty on parts and accessories
SPECIFICATIONS
150-PSI tank
3450-RPM capacitor start induction motor
8 oz. oil capacity
Product Description
The Job Boss Compressor comes equipped with a mobility kit for job site portability.5 gallon, Oil-Lube contractor style compressor is packed with features youll like. The High-flow airregulator and 2-port removable console are winning combinations for contractors looking for performance and versatility.5 gallon, mobile, contractor-style, single tank aircompressor. 2-port removable console to allow remote air regulation and higher pressure closer to the job site.5 gallon storage capacity air tank supports heavy use of brad nailers, staplers, and finish nailers; moderate use of roofing and framing nailers.5 gallon 150 PSI portable aircompressor, Mobility kit, ASME safety valve, and Operator manual.
found in C3551's reviews: Was pleased the second time - Very quiet, nice regulator, works well. I have not used satelite regulator option, I suppose if you were 500' from compressor it might be handy. Performs to expectations -
My C3551 arrived with a defective tank pressure guage. According to the output regulator, the cut-off pressure was right at 150 pounds and cut-in was near 120 pounds. I specifically wanted an oil lube compressor for durability, and this model fits that requirement. For handyman work or specialty trim nailing, this compressor is ideal. Good idea, but a bit more durabilty would be nice - I've been using this compressor for about 2 years of daily remodeling work in Colorado in all weather conditions. I bought it because I was tired of lugging around other compressors that didn't have wheels. The rolling design of this compressor is very good because it can easily go up and down stairs as well as over typical construction site obstacles.
After a few months of use the tank pressure gauge failed, and Porter Cable sent me a replacement.
After a year of use the motor kept tripping breakers, so I took the compressor in for service and it received a new compressor and motor.
Presently the regulator has been drifting a bit, but it hasn't annoyed me enough to get it fixed.
I work on job sites that have ancient compressors that continue to function flawlessly (but they're really heavy to move around), so I'm a bit worried by the problems I've noticed in only 2 years of use.
Because this compressor is oil lubricated, it does get sluggish in the winter. It also cannot supply as much air as the oil-free version. A trim subcontractor I know has the oil-free version and he has to rebuild his compressor annually with a $40 repair kit, so oil free isn't entirely without issues.
If you already have a compressor you like, I'd bolt some good wheels onto it and weld a nice handle onto the frame.
Update: The tank pressure gauge broke again, but I decided not to replace it. Porter Cable lacks quality control - After following the breaking procedure, I noticed that the regulator wouldn't let out any air. (Also, the compressor being so quiet won me over and I was willing to overlook few minor problems in order to keep it.
Porter Cable indicated the problem might be due to the regulator being blocked by a dope sealant, and suggested I remove it to check. I will receiving a replacement compressor tomorrow and I will post how that worked out, at that point I will be adjusting my rating for the product. way to go porter cable BEST MACHINE ON THE MARKET - this my 2nd aircompressor matter fact I was building a arbor for the back yard after pressure was reached for nailgun I work over 1 hour before the compressor recycled the only problem I have had is to set the pressure on the nail gun after about 2 tries it worked perfect. I really like the idea on the removeable gauge face the compressor stay in 1 spot and 50 to 100 feet you can attact the face to a fixed object so you can save on trips back to the compressor when you need another nailgun as in replaceing the framer to finishing gun . 1 man carpenter - I received the compressor from amazon with no defects. I do like the extra pressure to drive the nails in hard lumber. I run the compressor at 115 psi for the pasolode. The compressor does need time to build pressure to keep up with my 1 gun for nailing plywood. The compressor does have a quick recovery 10 to 15 seconds to cutoff so I'm able to nail with short breaks. For every other aspect of framing this compressor is a 5 star. And I know that the compressor rated at 4. The compressor is rated properly. The compressor does run quieter than the oiless compressor I did have. I am very happy with the compressor and can live with the short breaks during the nailing of plywood. Good mid-range job compressor. - My old dual tank wheel barrow-style compressor that I bought at Truitt and White Lumber in Berkeley lasted for ten years of moderate but daily use in my remodeling business. When that finally broke down I bought a pancake compressor as a quick fix, since I was doing more and more design work and gradually easing my way into retirement. So I decided to purchase this mid-range compressor.
As described below, the compressor is not the most durable. The pressure adjustment dial still sticks and comes off when you pull it out to adjust pressure. But overall, it's been a good handy compressor that I would recommend for anyone who is not engaged in heavy duty framing and running the thing 8 hours a day for months and years on end. For that you need the old double-tank wheelbarrow style compressor. Excellent Compressor for Framing or Finish Work - Lots of pressure and quick recovery powering my Hitachi NR83A2. A bit slow running an airfile. Good value- I am happy with this compressor. mine came damaged too! - The main pressure gauge was sheared off (behind the control panel) and the frame was dented and air filter busted. Great compressor for the size - After owning a craftsman 4gal unit, and have it malfunction on the first use (relief valve stuck open, not letting pressure build) and returning it, I looked into a better replacement. The Porter-Cable C3551 is a very nice compressor - I have a few compressors already - but they are too big and bulky to move around and my previous smaller 10 gallon compressor is getting a bit rough around the edges. 10 years old for a oil-less compressor is a pretty good.
With that said I wanted a new smaller compressor to aid in the remodel work I'm doing.
Upon receiving the compressor I gave it a quick once over.
The performance of the compressor is very good. After the 20 minute no pressure breakin, I immediately put it to work. It fills quick, cycles infrequently, and is fairly quiet.
I think this is one of the best small compressors out there. If you need a nice portable compressor - look no further. For me it came down to the DEWALT D55155 or this compressor.
Powered by 5.5 hp Honda engine
