Air compressor manual - Porter-Cable C3551, Porter-Cable C6110, Porter-Cable C5101, Porter-Cable C5510, Porter-Cable CPLDC2541S, Porter-Cable CPLDC2540S, Makita MAC700, Makita MAC2400, DeWalt D55151, DeWalt D55155

Air Compressor Manual - 1 2 3 4

Job Boss 12 Amp 2-1/2 Horsepower 4.5 Gallon Oiled Wheeled Single Hot Dog Compress \| Porter-Cable C3551
	$641.68 >> $349.99 by Porter-Cable 86 pounds; 2-year limited warranty Includes compressor, mobility kit, ASME safety valve, manual Cast-iron construction 12 amps; 150 psi, enough to operate 2 nailers at once; roll bar to protect motor and pump 2-1/2-horsepower 4-1/2-gallon oiled wheeled single hot dog compressor found in C3551's description: If you're a contractor looking for the right compressor, you've found it.--Kris Jensen-Van Heste From the Manufacturer Why lift when you can roll? The Job Boss Compressor comes equipped with a mobility kit for job site portability.5 gallon, Oil-Lube contractor style compressor is packed with features you’ll like. The High-flo air regulator and 2-port removable console are winning combinations for contractors looking for performance and versatility. This compressor is designed with a removable console for maximum mobility and air pressure.5 HP single tank air compressor Oil-lube air compressor for maximum durability 150-PSI tank pressure for longer tool run time, Quieter motor is easy on eardrums 120 V/ 60 hertz/1 phase motor Two pole, 3450-RPM capacitor start induction motor for maximum air delivery Includes 1-year limited warranty on parts and accessories SPECIFICATIONS 150-PSI tank 3450-RPM capacitor start induction motor 8 oz. oil capacity Product Description The Job Boss Compressor comes equipped with a mobility kit for job site portability.5 gallon, Oil-Lube contractor style compressor is packed with features youll like. The High-flow air regulator and 2-port removable console are winning combinations for contractors looking for performance and versatility.5 gallon, mobile, contractor-style, single tank air compressor. 2-port removable console to allow remote air regulation and higher pressure closer to the job site.5 gallon storage capacity air tank supports heavy use of brad nailers, staplers, and finish nailers; moderate use of roofing and framing nailers.5 gallon 150 PSI portable air compressor, Mobility kit, ASME safety valve, and Operator manual. found in C3551's reviews: Performs to expectations - The manual was easy to read and follow. I specifically wanted an oil lube compressor for durability, and this model fits that requirement. For handyman work or specialty trim nailing, this compressor is ideal. Porter Cable lacks quality control - After following the breaking procedure, I noticed that the regulator wouldn't let out any air. (Also, the compressor being so quiet won me over and I was willing to overlook few minor problems in order to keep it.) I contacted Porter Cable through email for suggestion, since nothing from the trouble-shooting section of the manual hinted on what might be the problem. I will receiving a replacement compressor tomorrow and I will post how that worked out, at that point I will be adjusting my rating for the product.
*15 Amp 2 Horsepower 25 Gallon Oil-Free Wheeled Vertical Compressor* \| Porter-Cable C6110**
	$295.55 >> $319.99 by Porter-Cable Cushioned handle grip, Standard Equipment: Compressor, High-FloSM air regulator and push to connect coupler and operating manual. Oil-Free Pump - No maintenance or spilled oil, Vertical tank configuration takes less floor space .9 (running) HP induction motor for long life, High-FloSM air regulator and push to connect coupler 150 PSI max for longer tool run time, 120 PSI cut-in pressure provides 30 PSI "Bonus Air" before a 90 PSI tool becomes inoperable 5.4 SCFM for faster tank recharge of 25 gal tank found in C6110's description: From the Manufacturer This oil free, space saving vertical, wheeled portable air compressor from Porter-Cable provides 25 gallons of air tank reserve at a 150 PSI maximum pressure which provides 71 percent more usable air over traditional 125 PSI maximum air pressure units operating tools that require 90 PSI. With a pressure switch controller that automatically restarts the motor at the 120 PSI falling tank pressure point you get this quicker motor/pump operation and bonus air delivery. Supports all nailing applications and moderate + air tool usage of most air tools. High air flow regulator, high flow quick coupler two gages are also included. Reserve air tank is ASME approved.

*15 Amp 1-1/2 Horsepower 20 Gallon Oil-Free Wheeled Single Hot Dog Compressor* \| Porter-Cable C5101**
	$280.60 >> $292.80 by Porter-Cable Full shroud for pump/motor protection, Cushioned handle grip, Standard Equipment: Compressor, High-FloSM air regulator and push to connect coupler, pneumatic tires and operating manual. Oil-Free Pump - No maintenance or spilled oil, Full pneumatic tires for ease of mobility 1.7 (running) HP induction motor for long life, High-FloSM air regulator and push to connect coupler 150 PSI max for longer tool run time, 120 PSI cut-in pressure provides 30 PSI "Bonus Air"before a 90 PSI tool becomres inoperable 5.7 SCFM for faster tank recharge of 20 gal tank found in C5101's description: From the Manufacturer This oil free, horizontal low profile, wheeled portable air compressor from Porter-Cable provides 20 gallons of air tank reserve at a 150 PSI maximum pressure which provides 71 percent more usable air over traditional 125 PSI maximum air pressure units operating tools that require 90 PSI. With a pressure switch controller that automatically restarts the motor at the 120 PSI falling tank pressure point you get this quicker motor/pump operation and bonus air delivery. Supports all nailing applications and moderate air tool usage of most air tools. High air flow regulator, high flow quick coupler two gages are also included. Reserve air tank is ASME approved.
*15 Amp 2 Horsepower 20 Gallon Oiled Wheeled Single Tank Compressor* \| Porter-Cable C5510**
	$387.26 >> $471.99 by Porter-Cable Cushioned handle grip, Standard Equipment: Compressor, High-FloSM air regulator and push to connect coupler, pneumatic tires and operating manual Full pneumatic tires for ease of mobility, Patented belt tensioning device 1.9 (running) HP induction motor for long life, High-FloSM air regulator and push to connect coupler, Oil-Lube Pump - for long life 150 PSI max for longer tool run time, 120 PSI cut-in pressure provides 30 PSI "Bonus Air" before a 90 PSI tool becomes inoperable 5.4 SCFM for faster tank recharge of 20 gal tank found in C5510's description: From the Manufacturer This very quiet 78 dBA, traditional belt drive oil lube, horizontal low profile, wheeled portable air compressor from Porter-Cable provides 20 gallons of air tank reserve at a 150 PSI maximum pressure which provides 71 percent more usable air over traditional 125 PSI maximum air pressure units operating tools that require 90 PSI. With a pressure switch controller that automatically restarts the motor at the 120 PSI falling tank pressure point you get this quicker motor/pump operation and bonus air delivery. Supports all nailing applications and moderate + air tool usage of most air tools. Includes 10 pneumatic wheels, foam padded metal handle, high air flow regulator/quick coupler and two gages. Reserve air tank is ASME approved.
*2.5 HP 4 Gallon Oil-Lube Air* Compressor \| Porter-Cable CPLDC2541S**
	$369.99 >> $358.51 by Porter-Cable Three year limited warranty Complete with high-flow regulator and quick-connect, pressure gauge and tank gauge Patent pending oil-lube system with ball bearing design Direct drive, no belts or adjustments are necessary 2.5 HP, 4.3-gallon oil-lube compressor found in CPLDC2541S's description: From the Manufacturer Porter-Cable is proud to introduce our first oil-lube compressor. When we first put our engineers on the task of designing an oil-lube compressor we gave them one priority; it could not have the same imported pump as all the other major brands have. Just as in a car, the lubrication system in the pump is the most vital part in a compressor. Now, take this revolutionary pump engineered to last over 3,000 hours of use and add in the "High Pressure Technology" and you have compressor that will run at 150 pounds per square inch (PSI).5 horsepower induction motor is safely shrouded and acts as a wind tunnel providing more than enough air to cool the unit down even under the most strenuous conditions.3 HP Running Patented oil lubrication system allows pump to be operated on an uneven surface Universal, High-FloSM, push-to-connect coupler in air outlet 150 PSI tank pressure, equivalent to a 7.3 gallon tank at 125 PSI, for 71% more stored work capacity 83 Dba Higher 120 PSI cut-in pressure assures nails will be completely driven in before pump cycles on Two pole, 3,450 RPM capacitor start induction motor for maximum air delivery High-FloSM air regulator for more work at higher pressure (125 PSI start and 150 PSI stop pressure switch) Low 12 Amp motor draw prevents accidental tripping of circuit breakers 4 gallon storage capacity air tank supports heavy usage of stapler, brad, finish, roofing and framing nailer Heavy duty cast iron cylinder construction and large 8 oz. oil capacity to assure long life Standard Equipment: Compressor, ASME safety valve, air regulator and gauges, 1/4" quick coupler, oil, and operating manual SPECIFICATIONS Lubrication: Oil Lube Gauges: 2 Quick Couple: 1/4" NPT Weight (Lbs. PSI: 150 SCFM Air Delivery @40 PSI: 5.4 SCFM Air Delivery @90 PSI: 4.
*2.5 HP 4 Gallon Oil-Lube Air* Compressor \| Porter-Cable CPLDC2540S**
	$580.00 by Porter-Cable Three year limited warranty Full roll cage with high flow regulator and dual quick-connects Patent pending oil-lube system with ball bearing design Direct drive, no belts or adjustments are necessary 2.5 HP, 4.3-gallon oil-lube compressor found in CPLDC2540S's description: From the Manufacturer Porter-Cable is proud to introduce our first oil-lube compressor. When we first put our engineers on the task of designing an oil-lube compressor we gave them one priority; it could not have the same imported pump as all the other major brands have. Just as in a car, the lubrication system in the pump is the most vital part in a compressor. Now, take this revolutionary pump engineered for maximum durability and life, and add in the "High Pressure Technology" and you have compressor that will run at 150 pounds per square inch (PSI).5 horsepower induction motor is safely shrouded and acts as a wind tunnel providing more than enough air to cool the unit down even under the most strenuous conditions. oil capacity to assure long life Patented oil lubrication system allows pump to be operated on an uneven surface Protected panel includes two universal High-FloSM push-to-connect couplers and larger, easy to read regulated air pressure gauge 150 PSI tank pressure, equivalent to a 7.3 gallon tank at 125 PSI, for 71% more stored work capacity 83 Dba Higher 120 PSI cut-in pressure assures nails will be completely driven in before pump cycles on Two pole, 3,450 RPM capacitor start induction motor for maximum air delivery High-FloSM air regulator for more work at higher pressure (125 PSI start and 150 PSI stop pressure switch) Specially designed protective transport handles Low 12 Amp motor draw prevents accidental tripping of circuit breakers 4 gallon storage capacity air tank supports heavy usage of stapler, brad, finish, roofing and framing nailer Standard Equipment: Compressor, ASME safety valve, air regulator and gauge, 1/4" quick coupler, oil, and operating manual SPECIFICATIONS Lubrication: Oil Lube Gauges: 2 Quick Couple: 1/4" NPT Weight (Lbs. PSI: 150 SCFM Air Delivery @40 PSI: 5.4 SCFM Air Delivery @90 PSI: 4. found in CPLDC2540S's reviews: *A- compressor* except for the regulator - I've been searching for a portable compressor for a couple of months now and near the end came up with three to chose from: the Emglo 55155, a Hitachi dual stack and this PC. Other compressors did meet these, but what draw me was the oil lube system that permits you to use it on uneven surfaces.5max) to not trip the circuit breakers, filtered intake (not output though) for longer motor life, shrouded motor for airflow from fan and good manual. The only thing I added at the universal coupler end is a water/air** filter.
*The Hotdog 12.4 Amp 2 Horsepower 2-1/2 Gallon Oiled Single Hotdog Compressor* \| Makita MAC700**
	$288.00 >> $176.40 by Makita 18 by 10 by 22 inches; 52 pounds; 1-year warranty 1/4-inch brass Makita universal coupler Cast-iron pump and roll cage construction 3.3 cfm delivered at 90 psi; low 1,720 rpm extends motor life and lowers noise 12.4 amp, 2-horsepower, 2-1/2-gallon oiled single hot dog compressor with handle found in MAC700's description: From the Manufacturer The new MAC700 - Hotdog compressor by Makita is blowing away the competition with built-in features such as a super quiet motor that draws only 12.0HP AIR COMPRESSOR 12. hot dog tank Low amp draw & oil lubricated Roll-bar handle Industrial air filter & cast iron cylinder Oil sight glass & lever handle ball valve Built-in thermal overload for motor protection MAC700 2HP AIR COMPRESSOR. found in MAC700's reviews: Great Product....Bad Manual - A well put together compressor that is wonderful for the weekend warrior. This compressor is well built and should last a long time. My only beef is that the instruction manual is pathetic and has not been updated. I assume that Makita used to ship this item with air filter attached because there is no mention in the manual that you have to install the filter. It is not difficult to perform this procedure, mind you, but it would be nice to have it mentioned in the manual under the section on setting up the compressor. C'mon Makita, hire an English editor for a day and update your manual! Oh, and include some pictures with your parts description! In addition, you may mention that you have to remove the temporary oil cap and install the separately packaged cap (also not mentioned in the m. Very good - The compressor is packed very well without any damage. One draw back is that its manual is not well written. After running it over 20 minuates, I discovered that I did not install the air filter. The manual did not mention it at all. It is as advertised - If you're considering an oil less compressor,,, don't. Read the manual and follow the break-in and maintenance procedures and off you go. This unit is not supposed to be a "contractor's" compressor. If you need a compressor for big job sites, buy an appropriate unit. Reviewer from Arizona - I am pleased with this Makita's compressor. Comparing it to other light weight/low capacity compressors I had before the engine noise is not that bad. For instance the air filter is place in an aluminum container whereas most other small compressors use plastic containers instead which can easily break off. I think they could have done a better job in writing their user manual. Great little compressor - As another poster mentioned, the manual does a poor job of telling you how to break-in. Be sure to fill with oil and install the air filter before starting. Serious PITA, but cost was minimal and repair works fine. All in all, a great little compressor, and the best choice if noise is a concern. Great little compressor - I have had this compressor for a couple of weeks now and really like it. I chose this model over the very popular oil-free pancake compressors mainly for it's compact size and low noise level. The unit is compact, but much heavier duty than similar Crftman compressors I saw at Sears. It came with a good owner's manual* and a bottle of oil. I would recommend this unit to anyone looking for an occasional use compressor and does not want something large or loud. *Great compressor, but check the box thouroughly before signing for delivery!* - After working with a friend's older version of this compressor for the last eight months, I decided to splurge and get my own. If this compressor is anything like the older model, it's going to last forever. It looks like someone must've dropped it, and from a pretty good height! One of the legs was bent about 2 inches, so the compressor would rock when set down. Fortunately, the compressor itself (external tubes and gauges and whatnot) are all fine. It's annoying, but I don't want to go through the exchange process and be without air for another two weeks. The startup process is fairly simple. The manual doesn't explain what goes where when you open the box, but it's reasonably self-evident. There are two plastic plugs on the compressor that need to come out. One covers the oil filler, and one covers the air intake port. You replace the plug on the air intake port (topmost plug) with the included air filter, and you replace the oil filler plug with the included oil cap. Then, open the air release valve at the very bottom of the air tank and run the compressor for 20 minutes. Check the oil level periodically, of course! On a related note, I also bought the Campbell Hausfeld MP520010AV air tool accessory kit to get me started. Quiet, Solid, Well Made - I wanted a portable compressor for using my nail guns at old houses, and was ready to replace my antique mastodon shop compressor. I was thinking I may have to buy two compressors, most portable units were too loud for the shop. A few weeks ago I bought a Ridgid brand "oil-free" compressor at Home Depot but it was so loud that I couldn't use it indoors, even covered with a chunk of old carpet. It had good air flow.3 CFM is higher than many of the 75-pound twin stack compressors I saw. To reduce cycling in the shop, I attached my 5-gallon air tank (the kind you use for putting air in a flat tire) to the tank side of the regulator with a T and snap coupler. I'm sure this is somewhere in the owners manual of things NOT to do.like don't use the compressor in the bathtub. It's a large, high quality compressor mounted on a small, portable tank. You'll get really spoiled if you're used to a noisy oil-less compressor.

*13 Amp 2-1/2 Horsepower 4 Gallon Oiled Twin Hot Dog Compressor* \| Makita MAC2400**
	$460.00 >> $249.00 by Makita 19-3/8 by 18 by 18-3/4 inches; 77 pounds; 1-year warranty 1/4-inch brass Makita universal coupler Cast-iron pump and roll cage construction 4.2 cfm delivered at 90 psi; low 1,720 rpm extends motor life and lowers noise 13 amp, 2-1/2-horsepower, 4-gallon oiled twin hot dog compressor with handle found in MAC2400's description: From the Manufacturer The new MAC2400 - Twin Stack air compressor by Makita is blowing away the competition.3 amps to operate, a lower 1720 RPM rating and a heavy duty Intake Air Filter system like no other, its easy to see how this unit will out last and outperform everyone else. Large automotive style industrial air filter for increased air intake and greater efficiency. found in MAC2400's reviews: Mac2400 Very Good - I received this compressor in excellent condition - no damage in shipping. Easy to setup; however since I've never used one of these I had to read the manual very careful to make sure I understood all terms used. The manual could be significantly improved by adding some figures with arrows (I had to refer to the parts exploded diagram several times). Compressor great, but has a couple of issues - This is a great compressor and is highly recommended. However, you need to be mindful that this compressor is _very_ heavy. It _is_ quiet, as far as compressors go. The other issue is that the manual is not very good. Perhaps Makita will work on making a manual that matches the quality of the compressor. Very pleased - This is my first air compressor, and I just received it yesterday so can't vouch for long-term quality, but I just wanted folks to know that it has ZERO damage. The air filter was packaged in a heavy plastic baggie along with the oil and manual. The thin paper manual has a few indentations from the wingnut on the air filter pressing into it, but the compressor unit itself is showroom clean. great compressor - I had no problems with the condition of my new compressor. The noise level is like advertised (fairly quiet). I was not impressed with the manual, but it was satisfactory. For the volume of work I will do, this is plenty of compressor and then some.
*14 Amp 2-1/2 Horsepower 4-Gallon Oiled Twin Hot Dog Compressor* \| DeWalt D55151**
	$449.35 >> $219.99 by DeWalt 18-1/2 by 15 by 16-3/4 inches; 60 pounds; 1-year warranty Includes DEWALT synthetic compressor oil and pressure regulator Cylinder constructed of cast iron Delivers 3.2 cfm at 100 psi; features overload protection to eliminate risk of motor damage 14 amp 2-1/2-horsepower 4-gallon oiled twin hot dog compressor with carrying handle found in D55151's description: From the Manufacturer This versatile compressor can perform a multitude of jobs, from roofing to finish to trim to home/hobby applications. The compressor delivers 3. Includes 3/8-inch regulator and initial fill of DeWalt synthetic air compressor oil. Includes DeWalt synthetic compressor oil Pressure regulator Warranty This DeWalt high-performance industrial tool comes with a warranty package that includes: 30-day, no-risk satisfaction guarantee One-year free service contract One-year warranty Product Description Portable electric powered compressor with 2 HP, high output motor. found in D55151's reviews: excellent compressor - Two months later, I open the box, take it out, and realize that the plastic cover is broken into many, many pieces! I was very disappointed! There was no visible damage anywhere on the compressor or the box it came in. So I opened the manual, and called 1-800 number for Dewalt. The guy said he is going to mail me the new cover right away, express shipping (I told him I need to use it in 3 days), I could not be without compressor. 15 minutes later the same guy from Dewalt calls me back, saying it would be better if he just shipped me a brand new compressor, express mail of course, as long as I agree to ship my unit back, free of charge. Now that's what I call customer service! I got the new unit, hooked it up, used it (and continue to use it) extensively (it's my only compressor), and it has never let me down. It may be a little loud, but I don't know which compressor is quiet. Dials are easy to use, drain plug as well, and it does not leak air.
*15 Amp 2-3/4 Horsepower 4 Gallon Oiled Single Hot Dog Compressor* \| DeWalt D55155**
	$676.00 >> $365.00 by DeWalt 23 by 23 by 13-1/2 inches; 68-1/2 pounds; 1-year warranty Includes DEWALT synthetic compressor oil and pressure regulator Cylinder constructed of cast iron 4-1/2 cfm delivered at 100 psi; dual soft start valve for cold-weather starts; oil-lubricated pump 15 amp 2-3/4-horsepower 4-gallon oiled twin hot dog compressor with carrying handle found in D55155's description: com Review At just a foot high and less than two feet wide out of the carton, this compressor was quite a bit smaller than we expected, so to be fair, we quickly lowered our expectations. The joke was on us, though, because this little powerhouse just doesn’t quit, and we learned that you can’t judge a compressor by its size. Emglo’s half-century in the compressor business is evident in this model, and with a couple of small exceptions (we’ll get into that in a minute), we don’t think anyone could make a finer piece of air power. Now, this may be a plus or a minus in your book, but we liked the fact that the compressor is factory set to power on at 100 psi an+d shut off at 120 psi, and the cycle time was under 15 seconds.) It has air aplenty for two nailers at once, and with that fast recovery, the job will get done in no time. In balance, this is one of the best compressor’s we’ve seen for the size, power, ruggedness and incredible portability it offers. Here’s to a great pairing of two great toolmakers.--Kris Jensen-Van Heste Product Description DeWalt's 2-horsepower, 4-gallon compressor features an oil-lubricated design with a cast-iron cylinder to guarantee job site durability. The new roll-cage design and integrated control panel protects the compressor and the controls from accidental damage. Carrying the compressor is easy, too: the flat design lets the user tote the compressor comfortably like a suitcase. The package comes with the initial fill of DeWalt synthetic air compressor oil. From the Manufacturer This 4-gallon hand-carry compressor was designed to meet the tough demands of the job site. The handle is situated to allow the user to carry the compressor with one hand in a natural walking position. The roll cage and integrated instrument panel protect the compressor and instruments from damage. Comes with the initial fill of DeWalt's synthetic air compressor oil. Includes DeWalt synthetic compressor oil 2 universal quick couplers Regulator Warranty This DeWalt high-performance industrial tool comes with a warranty package that includes: 30-day, no-risk satisfaction guarantee One-year free service contract One-year warranty Product Description 2 HP, 4 Gallon, Electric Single Tank Hand Carry Compressor, 4. found in D55155's reviews: Good machine, but some packaging and assembly issues - To my dissatisfaction, it arrived with a broken air filter and some loose items rolling around in the air tank. No, it wasn't the air filter parts, it was something metalic actually inside the closed tank! Amazon referred me to DeWalt who referred me to my local service center. Thanks to Amazon's incredibly fast and hassle-free process for returns, I had my replacement compressor less than a week later. Unfortunately, it too had a broken air filter. But since everything else was fine, I bought a filter locally (DeWalt's replacement has yet to arrive) for $10 and kept the compressor. Another surprise with the second shipment was the inclusion of oil, a dipstick, instructions to add oil, and a product manual. This was not in the first shipment and is REQUIRED before starting the unit which is something that as a first-time compressor buyer, I would not have known to do.