12 Air Compressor Tank Volt - 1   2   3   4   5   6   7   8   9
XPower Powerpack 300 Plus Portable Backup Power Source | Xantrex 852-1840
Xantrex Technologies 852-1840
$149.99
by Xantrex Technologies

Built-in emergency light for illumination at home or on the road
Vehicle jumper cables
250 psi air compressor for inflating tires and sports equipment
Operates 115-volt AC or 12-volt DC products anywhere
Provides up to 300 watts of AC power

found in 852-1840's reviews:
Does what it was made to do - They also put a power inverter on it so that you can power small 110-volt tools if necessary but don't expect it to provide the power of a gas-generator or your ac-mains, and there's a 12-volt cigarette outlet too for 12-volt tools. They put a small compressor on it and it works fine for emergencies, but it's not meant to inflate tires all the time like a Campbell-Hausfield 10-hp dual-stage compressor with 50-gallon tank, it's an emergency convenience, and that's the point that should be remembered. If you want to run your TV, air-conditioner, hot-water heater, well pump, washer/dryer, dishwasher, home theater system, or refridgerator, then buy a gasoline powered generator instead.
15 Amps/ 8Amps 2 Horsepower 17-Gallon Electic Wheeled Portable Compressor with Dual Vo | DeWalt D55585
DeWalt D55585
$1,812.29 >> $849.99
by DeWalt

Ball valve drain allows for quick and thorough tank draining
Dual voltage feature allows easy switching from 120 to 240 volts
Dual control feature allows start/stop or constant run option
Twin cylinder, cast iron, oil lubricated pump
8.4 cfm delivered at 100 psi with 17-gallon tank

found in D55585's description: From the Manufacturer
You will never run short of air again with this 2-horsepower electric wheeled compressor supported by an ASME-coded 17-gallon OSHA-recognized tank. It also features dual voltage, so you can change from 120-volt to 240-volt operation without added work. The user can quickly and completely drain the compressor by the ball valve drain, which won't clog like other models that use needle valves. The D55585 includes DeWalt's synthetic compressor oil and a 3/8-inch NPT pressure regulator.4 cubic feet per minute delivered at 100 psi, enables speedy recovery
  • Twin-cylinder, cast-iron, oil-lubricated pump with Emglo's 50 years of proven durability and reliability
  • 2-horsepower motor provides increased performance
  • Dual wheels make maneuvering easier on the worksite
  • Dual control feature allows start/stop or constant run operation
  • Dual voltage feature allows easy switching from 120- to 240-volt operation
  • ASME-coded 17-gallon OSHA-recognized tank
  • Ball valve drain allows for quick and thorough tank draining

    Specifications

    • Drive: belt drive
    • Horsepower: 2 hp
    • Tank size: 17 gallons
    • Power supply: 2-pole induction motor
    • Cubic feet per minute at 100 psi: 8.

    Includes

    • DeWalt synthetic compressor oil
    • 3/8-inch NPT pressure regulator

    Warranty
    This DeWalt high-performance industrial tool comes with a warranty package that includes:
    30-day, no-risk satisfaction guarantee
    One-year free service contract
    One-year warranty.

  • 15 Amp 7 Horsepower 60-Gallon Oiled Vertical Compressor | Porter-Cable CPLC7060V
    Porter-Cable CPLC7060V
    $832.24 >> $404.96
    by Porter-Cable

    Three-year warranty
    60-gallon tank supports heavy-duty, intermittent to continuous use of multiple tools
    Oil-lubricated pump with aluminum body and cast-iron cylinders for heat dissipation and durability
    7 hp induction motor for efficient operation
    High-pressure technology provides more usable air for longer run time

    found in CPLC7060V's description: From the Manufacturer
    New from Porter-Cable! This heavy-duty stationary air compressor has a high-pressure design that allows it to store as much air as a 77-gallon tank. This provides more usable air and longer run times between refills-it's like being able to fit 20 gallons of gas in a 15-gallon tank-you'll get more done! A 7 hp, 240-volt induction motor powers this unit for maximum efficiency. Supplies 12. A 60-gallon, ASME tank provides enough reserve for heavy-duty, intermittent, multi-tool usage. Includes compressor, tank gauge, and operator's manual.0 HP Running
  • 135 PSI - 77 gallon equivalent tank size as compared to conventional 125 PSI models
  • 84 Dba
  • Single stage, oil lubricated pump designed with aluminum body and head for best cooling and cast iron cylinder sleeves for best wear
  • Pump contains automotive style pistons, rings, and connecting rod
  • 240 Volt capacitor start induction motor with manual thermal overload protection
  • Large tank pressure gauge for easy visibility and better accuracy
  • 60 gallon air tank supports heavy duty, intermittent/continuous multi-tool usage
  • Full-size belt guard
  • Patented automatic belt tensioning system
  • Standard Equipment: Compressor, ASME safety valve, tank gauge, oil, and operating manual

    SPECIFICATIONS

    • Lubrication: Oil Lube
    • Tank Size Gal.0
    • Amps @240 Volts: 15
    • Max. PSI: 135
    • SCFM Air Delivery @40 PSI: 14.2
    • SCFM Air Delivery @90 PSI: 9.
  • - Ingersoll Rand Electric Stationary Air Compressor - 3 HP, 10.3 CFM @ 135 PSI, 230 Volt, Model# SS3
    Ingersoll Rand SS3L3
    $559.99 >> $559.99
    by Ingersoll Rand

    Tank Size: 60 gallon vertical
    Max PSI: 135 PSI
    PSI: 11.3 CFM @ 90 PSI; 10.3 CFM @ 135 PSI
    Volts: 230 Volts
    Motor: 3 HP with thermal overload and manual reset - single phase motor

    found in SS3L3's description: Product Description
    Maximum air power! More delivered air (CFM) gives you the power to do the job right and in less time.
    found in SS3L3's reviews:
    A cheap way to get more CFM... but its still cheap. - This air compressor is identical to my Ingersoll Rand SS3L3 compressor that I purchased through Northern Tool in the early summer of 2005. This is the first air compressor that I have ever owned, so it was a learning experience from the start.

    It is recommended that you purchase the IR SS3L3 startup kit as the compressor is delivered to you without any oil in it. When I plugged in the compressor to test it out, I found that the motor continued to run even as the gauge on the tank passed 130 psi. As it creeped closer to 135 psi (the limit printed on the tank), I pulled the plug.

    I ran the compressor off and on for several months without any major issues. a little bit of die grinding, I rotated the tires on my car using the impact wrench and air ratchet, I used it to blow dust off my work bench and check the air in my tires on a routine basis. I bought the compressor because I have several project cars, and I would like to begin the serious work of restoring them. Recently, I have been looking at plans for a sandblasting cabinet, and I am starting to doubt that this compressor will stand up to the task of sand blasting for extended periods. Things I have learned about the compressor since its purchase that have led me to this conclusion:

    1. (I swap between my compressor and my dryer on the only 230V outlet in my house). This borderline false advertising is similar to peak and RMS power ratings in audio amplifiers, though it is fairly standard operating procedure to rate motors in this fashion. Though it is quieter than a direct drive unit like the 30 gallon compressors sold at most hardware stores, 3450 RPM is still quite fast. With the pulley ratios, the compressor crank spins at 1200 RPM. Heavier duty systems might have the AC motor running at 1200-1750 RPM with the compressor running at ~700 RPM or less, resulting in a much quieter setup. There is apparently no available rebuild kit for the compressor itself, according to the local IR dealer, though they do sell gaskets and the oiling kit. It is a two cylinder, single stage compressor. The "valves" in the head are what I believe are called "reed valves", which are simply spring loaded "fingers" that cover holes in the cylinder head, and they move with the blowing/sucking of air as the pistons move in the cylinders (no mechanical actuation of the valves). The compressor can run fairly hot, especially when pressurizing the tank from zero pressure. I would like to add an intercooler in line to the tank as the compressed air is quite hot, and I think the compressor itself could use some more cooling. I bought some copper to fab up a larger heat sink for the compressor housing, though I haven't made it yet. The flywheel on the compressor is designed to move air over the unit, but I still think the design needs improvement. There is a flimsy petcock drain valve in the bottom of the tank that is difficult to access. I have not yet installed a regulator and filter in the system, and I haven't checked how much condensation has collected in the tank. (Note: Added 10/10/06 - I added a Swagelok right angle 1/4" male NPT to 1/4" tube adaptor to this drain orifice, then plumbed 1/4" tubing out from under the tank and connected this to a ball valve. This makes me want to install a condensor between the compressor and tank). Copper tubing is used to route compressed air from the compressor to the tank, and I think some improvements could be made there, as well. The oil reservoir drain plug is on the bottom of the crank case, however this is no practical way to drain the oil without spilling it all over the top of the tank. One could remove the compressor to change the oil, but a better soultion would be to insert a ball valve in the oil drain plug for easy draining. I suspect that the threading on the oil plug is standard NPT like all of the other fittings on the tank - possible 1/4" or 3/8".

    IR sells the SS5L5, which uses the same 60 gallon tank, but a 5 HP split phase 3450 RPM motor running a different two piston single stage compressor.

    My biggest complaints are the use of the split phase motor, the relatively cheap design of the compressor (aluminum rods and lack of rod bearings), the flimsy pressure switch, and the cheap fittings used all over the machine. I will continue to use this unit for some time, but I am already considering either building my own low RPM, true 4-5 HP air compressor from various parts suppliers, or just purchasing a new one from a company like Eaton Compressor. Like houses, I think good advice for someone looking to buy an air compressor is "buy the most you can afford". I for one like the idea of a compressor running at a quiet 750 RPM at a mere 73 dBa, as opposed to my high revving 1200 RPM SS3L3.

    (Note: Added 10/10/06 -- As far as safety is concerned, this item will never blow up and injure anyone - IR has installed safety valves all over this tank as the other reviewer mentioned. Meanwhile, my criticisms of this unit are based on what I'd like to see in a compressor, that is all.

    Perfect -

    I have owned this air compressor for about two years now and it was worth every penny. The compressor is excellent, So far I have run my compressor about 100 hours thus far. It has always supplied my with an ample amount of air when using air tools except if I run my impact for 10 minuets continuously then it drops to 70 psi. I would recommend this compressor to any one with out hesitation. I turned it on two years ago and it has been on ever sense it kicks on about every hour because there is a leak I have not fixed in my air system. Yes it puts of a lot of heat but if you do the math PV=nRt you will see that a lot of heat is given off compressing that much air. Also in response to the allegations that the tank was going to over pressurize If the switch failed and it continued to run there is a spring loaded safety valve on the power switch on the compressor so it is not possible to over pressurize it, mine hits about 133 before it kicks off.

    15 Amp 2 Horsepower 25 Gallon Oil-Free Wheeled Vertical Compressor | Porter-Cable C6110
    Porter-Cable C6110
    $295.55 >> $319.99
    by Porter-Cable

    Cushioned handle grip, Standard Equipment: Compressor, High-FloSM air regulator and push to connect coupler and operating manual.
    Oil-Free Pump - No maintenance or spilled oil, Vertical tank configuration takes less floor space
    .9 (running) HP induction motor for long life, High-FloSM air regulator and push to connect coupler
    150 PSI max for longer tool run time, 120 PSI cut-in pressure provides 30 PSI "Bonus Air" before a 90 PSI tool becomes inoperable
    5.4 SCFM for faster tank recharge of 25 gal tank

    found in C6110's description: From the Manufacturer
    This oil free, space saving vertical, wheeled portable air compressor from Porter-Cable provides 25 gallons of air tank reserve at a 150 PSI maximum pressure which provides 71 percent more usable air over traditional 125 PSI maximum air pressure units operating tools that require 90 PSI. With a pressure switch controller that automatically restarts the motor at the 120 PSI falling tank pressure point you get this quicker motor/pump operation and bonus air delivery. Supports all nailing applications and moderate + air tool usage of most air tools. A 120 volt, 1. High air flow regulator, high flow quick coupler two gages are also included. Reserve air tank is ASME approved.
    15 Amp 1-1/2 Horsepower 20 Gallon Oil-Free Wheeled Single Hot Dog Compressor | Porter-Cable C5101
    Porter-Cable C5101
    $280.60 >> $292.80
    by Porter-Cable

    Full shroud for pump/motor protection, Cushioned handle grip, Standard Equipment: Compressor, High-FloSM air regulator and push to connect coupler, pneumatic tires and operating manual.
    Oil-Free Pump - No maintenance or spilled oil, Full pneumatic tires for ease of mobility
    1.7 (running) HP induction motor for long life, High-FloSM air regulator and push to connect coupler
    150 PSI max for longer tool run time, 120 PSI cut-in pressure provides 30 PSI "Bonus Air"before a 90 PSI tool becomres inoperable
    5.7 SCFM for faster tank recharge of 20 gal tank

    found in C5101's description: From the Manufacturer
    This oil free, horizontal low profile, wheeled portable air compressor from Porter-Cable provides 20 gallons of air tank reserve at a 150 PSI maximum pressure which provides 71 percent more usable air over traditional 125 PSI maximum air pressure units operating tools that require 90 PSI. With a pressure switch controller that automatically restarts the motor at the 120 PSI falling tank pressure point you get this quicker motor/pump operation and bonus air delivery. Supports all nailing applications and moderate air tool usage of most air tools. A 120 volt, 1. High air flow regulator, high flow quick coupler two gages are also included. Reserve air tank is ASME approved.
    15 Amp 2 Horsepower 20 Gallon Oiled Wheeled Single Tank Compressor | Porter-Cable C5510
    Porter-Cable C5510
    $387.26 >> $471.99
    by Porter-Cable

    Cushioned handle grip, Standard Equipment: Compressor, High-FloSM air regulator and push to connect coupler, pneumatic tires and operating manual
    Full pneumatic tires for ease of mobility, Patented belt tensioning device
    1.9 (running) HP induction motor for long life, High-FloSM air regulator and push to connect coupler, Oil-Lube Pump - for long life
    150 PSI max for longer tool run time, 120 PSI cut-in pressure provides 30 PSI "Bonus Air" before a 90 PSI tool becomes inoperable
    5.4 SCFM for faster tank recharge of 20 gal tank

    found in C5510's description: From the Manufacturer
    This very quiet 78 dBA, traditional belt drive oil lube, horizontal low profile, wheeled portable air compressor from Porter-Cable provides 20 gallons of air tank reserve at a 150 PSI maximum pressure which provides 71 percent more usable air over traditional 125 PSI maximum air pressure units operating tools that require 90 PSI. With a pressure switch controller that automatically restarts the motor at the 120 PSI falling tank pressure point you get this quicker motor/pump operation and bonus air delivery. Supports all nailing applications and moderate + air tool usage of most air tools. A 120 volt, 1. Includes 10 pneumatic wheels, foam padded metal handle, high air flow regulator/quick coupler and two gages. Reserve air tank is ASME approved.
    20 Amp/ 10 Amp 2 Horsepower 8-Gallon Wheeled Oiled Twin Pontoon Compressor with Dual V | DeWalt D55580
    DeWalt D55580
    $1,531.92 >> $661.25
    by DeWalt

    Dual voltage feature allows easy switching from 120- to 240-volt operation
    Dual control feature allows start/stop or constant run operation
    Low profile design for easy maneuverability
    Twin cylinder, cast iron, oil lubricated pump
    8.4 cfm @ 100 psi for quick recovery

    found in D55580's description: Dual voltage feature allows easy switching from 120 to 240 volt operation. * Include DEWALT Synthetic Compressor Oil and 3/8" NPT pressure regulator.
    found in D55580's reviews:
    Couldn't be better - This compressor is as strong as you need, it runs several guns at a time. The dual Voltage and the continuos run option is definately a plus, It draws hard on a 120 volt system but runs smooth on the 220 volt hookup. The recovery time is quick and you don't have to stand around and wait, like my old compressor.
    Quick Flow 3-in-1 Air Compressor | Wagan 2014
    Wagan 2014
    $29.99 >> $17.49
    by Wagan

    Comes with 10-foot power cord that plugs into 12-volt car cigarette lighter
    Comes with 1 sports needle and 2 nozzle adapters
    Inflates average tires in 5-7 minutes
    Built-in work/emergency light
    275 PSI high pressure air compressor

    found in 2014's description: com Review
    It's about time somebody came out with one of these--hats off to Wagan! It's small, light, inexpensive, and needs only a 12-volt power supply. We doubt you'll be able to find a more versatile compressor for the price. --Kris Jensen-Van Heste

    Product Description
    The Wagan 3-in-1 Air Compressor is perfect for vehicles, bike tires, balls, air mattress, and more. A 12-volt power supply is all that is needed to run the unit. The special features include a high pressure compressor that generates 275 PSI, high air flow inflator for quick inflation, built-in light, and pressure gauge.

    Product Description
    Handy portable air pump runs from the car cigarette lighter. Be prepared for the unexpected with 12V tire air inflators. Air Pump Inflates: Bike Tires, Car Tires (SUV, Truck), Athletic Balls, Air Mattresses, Rafts, Inflatable Furniture, Air Tools. Air Pressure (max)of Tire Inflator: 275PSI Special Features of this 12 Volt Auto Air Inflator: High Pressure 275 PSI High Air Flow Inflator Built-in Work light/Emergency light Inflates average sized tires (16') in 5-10 minutes Pressure Gauge Reader Continuous Usage Time: Tire Inflator Has A Heavy Duty Motor. Accessories: 3 Nozzle adapters: collar, tire inflator nozzle, sports needle 12V Power Cord: 10 ft cord High Pressure Air Hose: 14' Air Hose with quick release valve connector Power Source of Tire Inflators: 12V cigarette lighter accessory receptacle Low Power Consumption.
    15 Amp 2 Horsepower 20 Gallon Oiled Wheeled Single Tank Compressor | Campbell Hausfeld VT6290
    Campbell Hausfeld VT6290
    $457.71 >> $409.99
    by Campbell Hausfeld

    Fully enclosed protective belt guard with "Directed" cooling fan.
    5 HP Peak motor provides significant air flow. Operates on 120/240 volt service. Pre-wired for 120V.
    Unique product design from the largest manufacturer of reliable and durable, single stage CAST IRON pumps in the USA
    20 Gallon ASME code tank for tough jobs.
    Rugged Cast Iron two cylinder pump provides up to 5,000 hours of extended life. Oil-Lubricated pump has a traditional design that is quieter and longer lasting.

    found in VT6290's description: From the Manufacturer
    The VT6290, 2 Running HP, wired for household current delivers enough air power to tackle tough jobs. The 20 gallon horizontal ASME code tank is very portable and will not take up too much valuable real estate in the garage or on the job. The twin cylinder, oil lubricated, cast iron single stage pump runs quieter - so the compressor can be used in the same area that the work is taking place. Solid cast iron units are up to 35% quieter than aluminum units with cast iron cylinder sleeves, and dramatically quieter than direct drive aluminum compressors. These compressors are made in the US with a 3 year warranty.

    Product Description
    mfr: Campbell Hausfeld Air Products Campbell Hausfeld is a recognized leader in the home improvement and automotive industry.

    SINGLE STAGE AIR COMPRESSOR. Single Stage Cast Iron Compressor5 HP Peak, 20 Gallon.
    found in VT6290's reviews:
    Might work if received undamaged.......and with oil...and a few fixes - The shipping box is flimsy and cannot adequately support nor protect the compressor and parts. Mine arrived with a broken regulator, pressure gauge and air-filter assembly all of which apparently snapped off during shipment with no visible exterior box damage.

    As the other reviewer also mentioned the compressor does NOT come with oil so be sure to have SAE30 air-compressor oil ready when it arrives. Also, you will need to provide your choice of air outlet connector.

    If it wasn't for the bad shipment packaging I'd say initially that the compressor is a good buy but if Campbell Hausfeld has so little regard to protecting their product in shipment to you I question the integrity of the machine itself.

    UPDATE 7/15: I am updating this review a full day after receiving and can add more to the trials and tribulations of purchasing a C-H compressor. The air filter assembly is currently taped but working until I can get a replacment. One leak occurred in the main pipeline to tank (seal was improperly installed), another in the undamaged tank pressure gauge (somone missed adding teflon tape) and the third in the pressure tubing to the cutoff switch (not tightened). All in all if you include travel time to Home Depot nearly 2-1/2 hours were spent just getting the compressor to work only to discover that there is a leak at weld where the pump mount attaches to the tank.

    On the plus side is the quietness and the nicely powered 120/240v motor. Do watch r gauge of wire (use 12ga min.) if using an extension cable as this compressor does draw a load when starting.

    IMHO I wouldn't order a product like this if you need it for an immediate job as it will take to either repair yourself or to return and await a replacement. I needed this compressor to replace my dead one and ordered it to coincide with my time at home as I could not expect my wife to unload it.

    VT6290 and FedEx - The box was busted on one side causing some of the content to spill outside (a tire and air filter). On top of that, FedEx delivered the box upside down, causing the discharge tube to bend, the air filter to separate from the pump, a busted pressure gauge and a bent handle bar. The tank takes around 4 minutes to fill up to 135 pounds of pressure.
    The compressor DOES NOT include oil. It takes 12 ounces of Mobil 1 10W-30 Synthetic oil. The air filter supplied causes the compressor to be kind of noisy.

    Except for the awful FedEx delivery, I am happy with the compressor. Free delivery, free air hose, no tax, and 10% off.

    12 Air Compressor Tank Volt - 1   2   3   4   5   6   7   8   9

    Porter-Cable (27)
    Campbell Hausfeld (18)
    DeWalt (14)
    Emglo (10)
    Thomas Compressors (9)
    Bostitch (9)
    Makita (6)
    Hitachi (5)
    Porter Cable (4)
    Grip Rite (3)
    GRIP-RITE (2)
    Palmgren (2)
    Ingersoll Rand (1)
    Wagan (1)
    Stanley Hand Tools (1)
    AccuSet (1)
    Q Industries (1)
    Senco (1)
    Xantrex Technologies (1)
    Black & Decker (1)

    Other Searches:

    12 Volt Air Compressor With Tank
    12 Air Compressor Tank Volt
    12 Volt Air Compressor
    12 Volt Air Compressors
    Air Compressor Volt
    24 Volt Air Compressor
    120 Volt Air Compressor
    Air Compressor 12 Volt
    120 Air Compressor Volt
    12 Volt Portable Air Compressor
    ©2006